ASTM Gradel, JIS Grade, TIA, RMI 25, TIMETAL 35A, ST Sheet and plate. ASTM B Gr1, Mil-T CP Bars and billets. ASTM B Gr1. Tube. ASTM B Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality Titanium Plates, Sheets & Coils, Titanium sheets & plates.
|Published (Last):||5 September 2008|
|PDF File Size:||8.41 Mb|
|ePub File Size:||2.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The utmost care must be used in sampling titanium for chemical analysis because of asym great affinity for elements such as oxygen, nitrogen, and hydrogen.
MPa C Single values are maximum. A superscript epsilon indicates an editorial change since the last revision or reapproval. Final product hydrogen shall be reported.
Approved May 1, Unalloyed titanium plus 0. If the results of the retest conform to the specication, then the retest values will become the test values for certication. Marking and Packaging For circles, the over thickness tolerances in this table apply to the diameter of the circle corresponding to the width ranges shown.
The test report shall, at minimum, indicate acceptable or unacceptable results. If the results for the retest fail to conform to the specication, the material will be rejected in accordance with Section This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.
Samples for analysis should be stored in suitable containers.
Each pair of these bends will place opposite surfaces of the sheet or plate material in tension. Two bends shall be made in the L direction and two in the T direction. There is no under tolerance in weight for titanium sheets, under tolerance being restricted by the permissible thickness variations.
The values given in parentheses are mathematical satm to SI units that are provided for information only and are not considered standard. G Properties for material in the solution treated condition.
TITANIUM ALLOYS TECHNICAL DATA
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. The bend shall be made on a radius equal to that shown in Table 1 for the applicable grade.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
A xstm in parentheses indicates the year of last reapproval. Only original conforming test results or the conforming retest results shall be reported to the purchaser. Alternate techniques are discussed in Guide E This abstract is a brief summary of the referenced standard.
For plates of irregular shape, the over thickness tolerances apply to the greatest width corresponding to the width ranges shown.
Referee Test and Analysis It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Mechanical properties for conditions other than annealed or plate thickness over 1 in. B Bend to Radius asgm Mandrel, T equals the thickness of the bend test specimen.
The percentage of titanium is determined by difference. The manufacturer shall not ship material that is outside the limits specied in Table 2 for the applicable grade.
Titanium Plates, Sheets & Coils
Special Flatness Requirements S3. The characters shall be not less than 38 in. Methods of Chemical Analysis Last previous edition approved in as B — 09a1. Permissible Variations in Dimensions 7. If shipped as descaled, sandblasted, or ground, the manufacturer shall be permitted to remove minor surface imperfections by spot grinding if such grinding does not reduce the thickness of the material below the minimum permitted by the tolerance for the thickness ordered.
Titanium Plates, Sheets & Coils, Titanium ASTM B Gr2 Plates, Titanium Gr5 Sheets
Sampling for Chemical Analysis 9. Therefore, product analysis for elements not listed in Table 2 shall not be required unless specied and shall be considered to be in excess of the intent of this specication. In cutting samples for analysis, the operation should be carried out insofar as ast, in a dust-free atmosphere because utmost care must be used in sampling titanium for chemical analysis due to its great affinity for elements such as oxygen, nitrogen, and hydrogen.
Bend tests are not applicable to material 2b65 0. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. D Other elements need not be reported unless the concentration level is greater than 0.